Plumbing Essentials: An Essential for When Installing a Bathtub
Plumbing Essentials: An Essential for When Installing a Bathtub
Blog Article
The article author is making a few good points related to A Step-by-Step Guide to Installing a Bathtub as a whole in the content just below.

Setting up a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily available, the project can relocate speedily; if you need to open a wall surface to remove the old tub and position the new bathtub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will need an assistant to move out the old bathtub and embeded in the new one. See to it you have qualified yourself for the work and fit trying it. Instead of working with a specialist to take over a halfway-completed project, it is far better to consider utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This post will help you install a new bath tub in your washroom if you have actually already bought a brand-new tub and also do not need to transform the arrangement of your previous water pipes.
Your tools and product list must make up the following:
Preparing for the Installation
To start with, the supporting structure supplied with the bath needs to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any water remaining in the system. The procedure of removing the existing taps can be quite bothersome as a result of the limited gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the tub in the called for placement. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the spirit level reads degree.
To install faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water supply as well as check all joints and also new pipework for leakages and tighten them if needed. Fill the tub and additionally inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub must wait until the tub has been utilized at the very least once as this will settle it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in location between the faucet and the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type needs to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, bring about complications with dampness as well as possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components as well as installations. They are marketed in tubes and cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the bath tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you like more info about Installing A Bathtub? Place a remark directly below. We'd be interested to listen to your insights about this article. We are looking forward that you come back again soon. If you liked our article plz be sure to share it. We treasure reading our article about How to Install a Bathtub Yourself.
Save time, call now! Report this page